The State-owned Assets Supervision and Administration Commission of the State Council recently formulated the Measures for the Administration of Employees and Directors of Pilot Enterprises of State-owned Sole Proprietorship Enterprises (Trial), stating that the following persons shall not serve as directors of the company's employees: the secretary of the company's party committee (party group) and the deputy secretary of the party committee and secretary of the discipline inspection committee who are not concurrently the chairman of the labor union ( Head of the discipline inspection team); general manager, deputy general manager and chief accountant of the company.
The Measures pointed out that employee directors refer to the company's employees who are democratically elected and approved by the State-owned Assets Supervision and Administration Commission of the State Council as directors of the company. At least one employee director of the company's board of directors.
The Measures stipulate that the employee's directors shall meet the following conditions: democratically elected by the company's employees; have good conduct and a good mass base; have relevant legal knowledge, abide by laws, administrative regulations and company regulations, and keep company secrets; The company's operation and management, with relevant knowledge and work experience, has strong ability to participate in business decision-making and coordination and communication; other conditions stipulated by the "Company Law" and other laws and regulations.
According to the method, employee directors represent the employees to participate in the exercise of their functions and powers, enjoy the same rights as other directors of the company, and assume corresponding obligations. The term of office of the employee directors shall not exceed three years, and the term of office shall expire and may be re-elected. During the term of the employee director, the company shall not reduce the salary and terminate the labor contract due to the reasons for performing the duties of the director.
The authenticity of this information has not been confirmed by the international electrical network, for your reference only.
A 24V Dc Motor Consistency is good, reliable performance, low malfunction, torque, motor no-load and load running more smoothly and the lowest in 50 decibels
Functions: 24V dc motor rotor part of the armature iron core, armature, commutator and other devices, 24V dc motor is suitable for most of the electronic products, such as Electric curtains, car, sweeping robot, no hakaze fan, etc
Areas of application:
Method of use: the best stable in horizontal plane, installed on the 24V dc motor output shaft parts, cannot use a hammer to knock, knock prone to press into the 24V dc motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
24V dc motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a 24V dc motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
24V dc motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
The longevity of geared motors is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
24V Dc Motor,24V Dc Micro Motor,24V Dc Electrical Motor,24V Micro Dc Motor
Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com