(1) Compressive strength: In the electric field, the insulating material breaks down when the electric field strength increases to a certain limit. The electric field strength of this insulation breakdown is called the dielectric strength (also called dielectric strength or dielectric strength), and is usually expressed as a voltage KV value that a 1 mm thick insulating material can withstand.
(2) Tensile strength: The tensile force per unit sectional area of ​​the insulating material can withstand, for example, the glass can withstand 140 kilograms per square centimeter of cross-sectional area.
(3) Density: The mass per cubic meter of insulation material, for example 2 grams per cubic meter of sulfur.
(4) Coefficient of expansion: The extent to which the insulator increases in volume after it is heated.
3. Heat-resistant grades of insulating materials (1) Class Y insulating materials: natural textiles such as wood, cotton, and fibers, textiles based on acetate and polyamide, and materials that are easily decomposed and have a low melting point.
Extreme operating temperature: 90 degrees.
(2) Class A insulating materials: Grade Y materials impregnated with mineral oils and impregnated with oil or oleoresin composites, insulation of enameled wire, varnished cloth, lacquer, and oil paint. Asphalt paint and so on.
Limit working temperature: 105 degrees.
(3) Class E insulating materials: Polyester film and A-grade material composite, glass cloth, oil-based resin paint, polyvinyl acetal high-strength wire, vinyl acetate heat-resistant wire.
Extreme operating temperature: 120 degrees.
(4) Class B insulation material: polyester film, impregnated mica, glass fiber, asbestos, etc., with appropriate resin, polyester paint, polyester enameled wire.
Extreme operating temperature: 130 degrees.
(5) Class F insulation materials: mica products reinforced with organic fiber materials, glass wool and asbestos, glass wool cloth, laminated products based on glass wool cloth and asbestos fiber reinforced with inorganic materials as reinforcement and stone belts Mica powder products chemical thermal stability better polyester or alkyd materials, composite silicone organic polyester paint.
Limit working temperature: 155 degrees.
(6) Class H insulating materials: mica products without reinforcement or reinforcement with inorganic materials, thickened F-class materials, composite mica, silicone mica products, silicon organic paint silicone organic rubber polyimide composite glass cloth, Composite film, polyimide paint and so on.
Limit working temperature: 180 degrees.
(7) Class C insulating materials: Inorganic materials that do not use any organic binder and agent grade infusions, such as quartz, asbestos, mica, glass, and electric porcelain materials.
Limit working temperature: 180 degrees or more.
An ADSL filter separates the analogue voice-frequency signals from the ADSL (broadband) data signals(Broadband being defined as data transfer greater than 128KBPS.)
If ADSL filter/splitters are not used, the ADSL data signals are heard as "noise" on any equipment connected to the "normal" telephone-line. Apart from being annoying during a telephone conversation, there is the possibility that the additional ADSL signals may cause problems with alarm-units (etc) that may be connected across the line.
This ADSL-interference is illustrated in the diagram below that shows how the unfiltered ADSL data signals appear across the "standard" telephone equipment.
We can supply you ADSL Splitter,ADSL Filter, Adsl Modem Splitter,Telephone Splitter,adsl2+ splitter,adsl filter splitter, ,adsl dsl filter splitter,adsl in line splitter,adsl filter and splitter, ,rj11 splitter, broadband splitter, mdf splitter, adsl modem filter with a good quality and best price.
ADSL Splitter
ADSL Splitter, 2Wire DSL Filter, Adsl Modem Splitter, Telephone Splitter, ADSL Splitter Filter, Splitter ADSL
NINGBO YULIANG TELECOM MUNICATIONS EQUIPMENT CO.,LTD. , http://www.yltelecom.com